top of page

GOODWE
INVERTER GUIDE

+ SETTINGS + COMMUNICATION + TROUBLESHOOTING

The Goodwe inverters are fully compatible with the Hubble range of batteries.
The following field guide will assist with the correct battery settings you should use.

​

For further detailed information ensure you read the manual of the supplied battery regarding setup and installation instructions.

​

*Please note that our batteries are currently only compatible with the ES 5000 series.

 

WARNING

​

Working with high-voltage systems is dangerous. Do not attempt to modify your inverter and battery setup unless you are certain you understand the risk. Speak to a qualified electrician if you are unsure.

INVERTER EXAMPLE

Goodwe Inverter

INVERTER SETTINGS
 

Model
Voltage
Equalised
Float
Cutoff
Charge Amps
Max Discharge Current
S-SERIES
12V
14
14
12
30A
100A
X-100
48V
52.8
52.8
44
30A
100A
X-101
48V
53.8
53.8
44
30A
100A
X-200
36V
41.5
41.5
34
30A
100A
AM-2
48V
53.8
53.8
44
30A
100A
AM-3
48V
53.8
53.8
44
20A
50A
AM-4
24V
29
28.5
22
30A
100A
AM-5
48V
55.2
55.2
47
30A
100A
AM-10
48V
55.2
55.2
47
60A
150A
BLADE
48V
55.2
55.2
47
50A
200A

You can monitor your Goodwe inverter using the PV Master app. The below settings are the recommended settings to use for the corresponding Hubble Energy battery, as seen on the PV Master App.

 

You can download the PV Master app on either IOS or Android from their respective app stores.

OPERATION MODE

Goodwe Inverter setup guide

WORK STATUS

Goodwe Inverter setup guide

SYSTEM DATA

Goodwe Inverter setup guide

PIN LAYOUTS & CLOUDLINK

Hubble Energy recommends the Cloudlink Device on Growatt installations. It is not required but recommended.

CLOUDLINK

The Cloudlink will connect to the Battery via:

​

Cloudlink’s (Serial/RJ12 Port) to the Battery (RS232/RJ12 Port)

​

(Black Cable) – RJ12 to RJ12 (450mm) cable.

RJ45 PIN LAYOUTS

The Goodwe Inverter will connect to the Battery via:

​

Inverter (CAN Port) to Battery (CAN Port)

​

Straight RJ45 to RJ45 wire - 1500mm. 

​

Ensure that the clip is pointed away from you when counting the pins.

 

PIN
Inverter
X-101/AM-4/AM-2
AM-5/AM-10
Blade
1
-
-
-
-
2
-
GROUND
-
-
3
-
-
-
-
4
CANH
CANH
CANH
CANH
5
CANL
CANL
CANL
CANL
6
-
-
-
-
7
-
-
-
-
8
-
-
-
-

FINAL STEP TO GROWATT SPF 5000 ES SERIES INVERTER:

To connect battery BMS, need to set the battery type as “LI” in Program 05.
After set “LI” in Program 05, it will switch to Program 36 to choose communication protocol. You can choose RS485 communication protocol, which is from L01 to L50, and you can also choose CAN communication protocol which is from L51 to L99.

 

4 & 5 Pin Layout image reference seen below:

Goodwe Inverter setup guide

2, 4 & 5 Pin Layout image reference seen below:

Goodwe Inverter setup guide

HUBBLE DIP SWITCH SETTINGS

FOR MULTIPLE BATTERY INSTALLATION

For correct setup and communication, each battery needs a unique serial address to communicate. If you are only using one battery in your setup, consider this the master battery and ensure you set it to address 1.

AM-2, AM- 4 & BLADE DIP SWITCHES

ADDRESS
SWITCH POSITIONS
SWITCH POSITIONS
SWITCH POSITIONS
SWITCH POSITIONS
#1
#2
#3
#4
1
ON
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
3
ON
ON
OFF
OFF
4
OFF
OFF
ON
OFF
5
ON
OFF
ON
OFF
6
OFF
ON
ON
OFF
7
ON
ON
ON
OFF
8
OFF
OFF
OFF
ON
9
ON
OFF
OFF
ON
10
OFF
ON
OFF
ON
11
ON
ON
OFF
ON
12
OFF
OFF
ON
ON
13
ON
OFF
ON
ON
14
OFF
ON
ON
ON
15
ON
ON
ON
ON

AM-5 & AM-10 DIP SWITCHES (4-DIP VERSION)

ADDRESS
SWITCH POSITIONS
SWITCH POSITIONS
SWITCH POSITIONS
SWITCH POSITIONS
#1
#2
#3
#4
1
OFF
OFF
OFF
OFF
2
ON
OFF
OFF
OFF
3
OFF
ON
OFF
OFF
4
ON
ON
OFF
OFF
5
OFF
OFF
ON
OFF
6
ON
OFF
ON
OFF
7
OFF
ON
ON
OFF
8
ON
ON
ON
OFF
9
OFF
OFF
OFF
ON
10
ON
OFF
OFF
ON
11
OFF
ON
OFF
ON
12
ON
ON
OFF
ON
13
OFF
OFF
ON
ON
14
OFF
ON
ON
ON
15
ON
ON
ON
ON

AM-10 (8-DIP VERSION)

ADDRESS
SWITCH POSITIONS
SWITCH SETTINGS
SWITCH SETTINGS
SWITCH SETTINGS
SWITCH SETTINGS
SWITCH SETTINGS
SWITCH SETTINGS
#1
#2
#3
#4
#5
#6
Mark (#7 & #8)
0
ON
ON
OFF
OFF
OFF
OFF
Mastery Battery/Enable CAN BUS Port - ON
1
OFF
OFF
OFF
OFF
OFF
OFF
Slave 2 - OFF
2
OFF
ON
OFF
OFF
OFF
OFF
Slave 3 - OFF
3
OFF
OFF
ON
OFF
OFF
OFF
Slave 4 - OFF
4
OFF
ON
ON
OFF
OFF
OFF
Slave 5 - OFF
5
OFF
OFF
OFF
ON
OFF
OFF
Slave 6 - OFF
6
OFF
ON
OFF
ON
OFF
OFF
Slave 7 - OFF
7
OFF
OFF
ON
ON
OFF
OFF
Slave 8 - OFF
8
OFF
ON
ON
ON
OFF
OFF
Slave 9 - OFF
9
OFF
OFF
OFF
OFF
ON
OFF
Slave 10 - OFF
10
OFF
ON
OFF
OFF
ON
OFF
Slave 11 - OFF
11
OFF
OFF
ON
OFF
ON
OFF
Slave 12 - OFF
12
OFF
ON
ON
OFF
ON
OFF
Slave 13 - OFF
13
OFF
OFF
OFF
ON
ON
OFF
Slave 14 - OFF
14
OFF
ON
OFF
ON
ON
OFF
Slave 15 - OFF

FREQUENTLY ASKED QUESTIONS

How do you set up multiple batteries?

See table above and check your product manual for a more detailed explanation. You will have to set dip switch settings per battery to give them a unique address. You also must connect the included RJ45 battery link cables into the "Battery Link" port of each battery. Ensure your master battery dip switch 1 is on, 2,3,4 is OFF.  Only the master battery CAN Bus will be enabled. You can then connect the Hubble Cloudlink into the CAN port of the master battery for communications to work.

Do I have to use the communication battery link cables if I don’t want to monitor or have communications?

Short answer No. However, it is recommended to still connect the battery links and set the correct addresses. This also needs to be done if you want to connect a Hubble Cloudlink.

bottom of page