LUXPOWER
INVERTER GUIDE
+ SETTINGS + COMMUNICATION + TROUBLESHOOTING
Hubble is officially recognised and fully integrates with Luxpower inverters. The following field guide will assist with the correct battery settings you should use.
​
For further detailed information ensure you read the manual of the supplied battery regarding setup and installation instructions.
​
*12kW Luxpower Inverters are still under testing.
​
WARNING
​
Working with high-voltage systems is dangerous. Do not attempt to modify your inverter and battery setup unless you are certain you understand the risk. Speak to a qualified electrician if you are unsure.
INVERTER EXAMPLE

INVERTER SETTINGS
IMPORTANT
On the inverter, setup the charge/discharge profile AND setup the allowed charging times (P1, P2 and P3). (The default settings won’t allow the inverter to charge the battery using Mains power).
Model | Voltage | Equalised | Float | Cutoff | Charge Amps | Max Discharge Current |
---|---|---|---|---|---|---|
S-SERIES | 12V | 14 | 14 | 12 | 30A | 100A |
X-100 | 48V | 52.8 | 52.8 | 44 | 30A | 100A |
X-101 | 48V | 53.8 | 53.8 | 44 | 30A | 100A |
X-200 | 36V | 41.5 | 41.5 | 34 | 30A | 100A |
AM-2 | 48V | 53.8 | 53.8 | 44 | 30A | 100A |
AM-3 | 48V | 53.8 | 53.8 | 44 | 20A | 50A |
AM-4 | 24V | 29 | 28.5 | 22 | 30A | 100A |
AM-5 | 48V | 55.2 | 55.2 | 47 | 30A | 100A |
AM-10 | 48V | 55.2 | 55.2 | 47 | 60A | 150A |
BLADE | 48V | 55.2 | 55.2 | 47 | 50A | 200A |
STEPS TO CONNECT THE LUXPOWER LXP5K HYBRID:
-
Set Hubble MASTER dip to 1000 if AM-2 or AM-4. If AM-5 or AM-10 model set master dip to 0000.
-
Set Hubble Slaves to their respective addresses as per manual.​
-
Use CAN out on MASTER to Luxpower inverter.
-
Go to BATTERY Settings.
-
Select Lithium.
-
Select PYLON
STEPS TO CONNECT TO THE LUXPOWER SNA5KW:
-
Set Hubble MASTER dip to 1000 if AM-2 or AM-4. If AM-5 or
AM-10 model set master dip to 0000. -
Set Hubble Slaves to their respective addresses as per manual.
-
Use CAN out on MASTER to Luxpower inverter.
-
On the SNA, go to the MENU.
-
Select option 3 for Battery settings.
-
Select Lithium battery.
-
Select BRAND 2
PIN LAYOUTS & CLOUDLINK
*Please note: Hubble Energy recommends the Cloudlink Device on Luxpower installations. It is not required but recommended.
Check both the user-manual and the packaging of your inverter for its CAN pinout. Some Luxpower units use pins 4 and 5, whereas others still use pins 3 and 4.
CLOUDLINK
The Cloudlink will connect to the Battery via:
​
Cloudlink’s (Serial/RJ12 Port) to the Battery (RS232/RJ12 Port)
​
(Black Cable) – RJ12 to RJ12 (450mm) cable.
RJ45 PIN LAYOUTS
The Luxpower Inverter will connect to the Battery via:
​
Inverter (CAN Port) to Battery (CAN Port)
​
Straight RJ45 to RJ45 wire - 1500mm.
​
Ensure that the clip is pointed away from you when counting the pins.
LXP RANGE: LUXPOWER USING PINS 3 & 4 FOR INVERTER
PIN | Inverter | X-101/AM-4/AM-2 | AM-5/AM-10 | Blade |
---|---|---|---|---|
1 | - | - | - | - |
2 | - | - | - | - |
3 | CANL | - | - | - |
4 | CANH | CANH | CANH | CANH |
5 | - | CANL | CANL | CANL |
6 | - | - | - | - |
7 | - | - | - | - |
8 | - | - | - | - |
Please Note: The LXP is a hybrid inverter that requires solar to charge the battery to 100%.
SNA RANGE: LUXPOWER USING PINS 4 & 5 FOR INVERTER
PIN | Inverter | X-101/AM-4/AM-2 | AM-5/AM-10 | Blade |
---|---|---|---|---|
1 | - | - | - | - |
2 | - | - | - | - |
3 | - | - | - | - |
4 | CANH | CANH | CANH | CANH |
5 | CANL | CANL | CANL | CANL |
6 | - | - | - | - |
7 | - | - | - | - |
8 | - | - | - | - |
3 & 4 Pin Layout image reference seen below:

4 & 5 Pin Layout image reference seen below:

HUBBLE DIP SWITCH SETTINGS
FOR MULTIPLE BATTERY INSTALLATION
For correct setup and communication, each battery needs a unique serial address to communicate. If you are only using one battery in your setup, consider this the master battery and ensure you set it to address 1.
AM-2, AM- 4 & BLADE DIP SWITCHES
ADDRESS | SWITCH POSITIONS | SWITCH POSITIONS | SWITCH POSITIONS | SWITCH POSITIONS |
---|---|---|---|---|
#1 | #2 | #3 | #4 | |
1 | ON | OFF | OFF | OFF |
2 | OFF | ON | OFF | OFF |
3 | ON | ON | OFF | OFF |
4 | OFF | OFF | ON | OFF |
5 | ON | OFF | ON | OFF |
6 | OFF | ON | ON | OFF |
7 | ON | ON | ON | OFF |
8 | OFF | OFF | OFF | ON |
9 | ON | OFF | OFF | ON |
10 | OFF | ON | OFF | ON |
11 | ON | ON | OFF | ON |
12 | OFF | OFF | ON | ON |
13 | ON | OFF | ON | ON |
14 | OFF | ON | ON | ON |
15 | ON | ON | ON | ON |
AM-5 & AM-10 DIP SWITCHES (4-DIP VERSION)
ADDRESS | SWITCH POSITIONS | SWITCH POSITIONS | SWITCH POSITIONS | SWITCH POSITIONS |
---|---|---|---|---|
#1 | #2 | #3 | #4 | |
1 | OFF | OFF | OFF | OFF |
2 | ON | OFF | OFF | OFF |
3 | OFF | ON | OFF | OFF |
4 | ON | ON | OFF | OFF |
5 | OFF | OFF | ON | OFF |
6 | ON | OFF | ON | OFF |
7 | OFF | ON | ON | OFF |
8 | ON | ON | ON | OFF |
9 | OFF | OFF | OFF | ON |
10 | ON | OFF | OFF | ON |
11 | OFF | ON | OFF | ON |
12 | ON | ON | OFF | ON |
13 | OFF | OFF | ON | ON |
14 | OFF | ON | ON | ON |
15 | ON | ON | ON | ON |
AM-10 (8-DIP VERSION)
ADDRESS | SWITCH POSITIONS | SWITCH POSITIONS | SWITCH POSITIONS | SWITCH POSITIONS | SWITCH POSITIONS | SWITCH POSITIONS | SWITCH POSITIONS |
---|---|---|---|---|---|---|---|
#1 | #2 | #3 | #4 | #5 | #6 | Mark (#7 & #8) | |
0 | ON | ON | OFF | OFF | OFF | OFF | Mastery Battery/Enable CAN BUS Port - ON |
1 | OFF | OFF | OFF | OFF | OFF | OFF | Slave 2 - OFF |
2 | OFF | ON | OFF | OFF | OFF | OFF | Slave 3 - OFF |
3 | OFF | OFF | ON | OFF | OFF | OFF | Slave 4 - OFF |
4 | OFF | ON | ON | OFF | OFF | OFF | Slave 5 - OFF |
5 | OFF | OFF | OFF | ON | OFF | OFF | Slave 6 - OFF |
6 | OFF | ON | OFF | ON | OFF | OFF | Slave 7 - OFF |
7 | OFF | OFF | ON | ON | OFF | OFF | Slave 8 - OFF |
8 | OFF | ON | ON | ON | OFF | OFF | Slave 9 - OFF |
9 | OFF | OFF | OFF | OFF | ON | OFF | Slave 10 - OFF |
10 | OFF | ON | OFF | OFF | ON | OFF | Slave 11 - OFF |
11 | OFF | OFF | ON | OFF | ON | OFF | Slave 12 - OFF |
12 | OFF | ON | ON | OFF | ON | OFF | Slave 13 - OFF |
13 | OFF | OFF | OFF | ON | ON | OFF | Slave 14 - OFF |
14 | OFF | ON | OFF | ON | ON | OFF | Slave 15 - OFF |